产品详情
查看大图

  • 产品名称：交直流电流探头

  • 产品型号：TCP0150
  • 产品厂商：其它品牌
  • 产品文档：
你添加了1件商品 查看购物车
简单介绍：
交直流电流探头
详情介绍：
 
产品特点

   * 容易进行高精度AC/DC电流测量，操作简便，直流电流精度典型值≤1%； 
   * 带宽DC~20MHz，电流从±5mA到150A有效值，可满足大电流和小电流测试需要； 
   * 具有自动匹配刻度单元，并在示波器显示屏上读出； 
   * 在ATE设备通过GPIB接口可进行远程编程； 
   * 容易退磁和自动归零。 
   * 适用示波器型号：DPO4032、DPO4034、DPO4054、DPO4104
   * MSO4032、MSO4034、MSO4054、MSO4104
   * 部分DPO7000系列示波器。
Features & Benefits
Easy to Use and Accurate AC/DC Current Measurements
Connects Directly to DPO4000, MSO4000 and DPO7000 Series Oscilloscopes Using the TekVPI Probe Interface
DC to 20 MHz Bandwidth
150 A RMS Maximum Current Capability
500 A Peak Pulse Current Capability
High Accuracy with Typically Less than 1% DC Gain Error
Accurately Measures Current levels as low as 5 mA
Low Noise and DC Drift
Provides Automatic Units Scaling and Readout on the Oscilloscope's Display
Remote Programmable GPIB Control for ATE systems
Split-Core Probe Head Construction Allows Easy Connection to Conductors
Easy to Degauss and Autozero
Setup Controls and Probe Status and Diagnostic Indicators are Provided on Both the Probe Hardware and via an Easy-to-Access Scope UI Display Menu
Applications
Power Supplies
Semiconductor Devices
Power Inverters/Converters
Electronic Ballasts
Industrial/Consumer Electronics
Motor Drives
Transportation Systems
Note: Requires DPO7000Series Firmware Version 3.0.2 or greater. Requires DPO4000/MSO4000 Firmware Version 2.06 or greater.
TCP0150 is a high performance and easy-to-use 150 A AC/DC current probe designed for use and direct connection (without the need of an additional power supply) to the TekVPI™ probe interface used on Tektronix DPO4000, MSO4000 and DPO7000 Series oscilloscopes. This AC/DC current measurement probe provides 20 MHz of frequency bandwidth with selectable range control for 25 A and 150 A measurement ranges. It also provides low current measurement capability and accuracy to current levels as low as 5 mA per division — important for achieving broad dynamic current range of high-level and low-level measurement signals.
Characteristics
Warranted

Bandwidth
DC to ≥20 MHz (-3dB). Derate with Frequency. See Figure 1. (Calculated from Rise Time BW = .35/Rise Time)
Rise Time
≤17.5 ns
Max RMS Current
150 A
Max Peak Pulse Current
500 A
Minimum Sensitivity
5 mA (on oscilloscope’s 1 mV/div setting)
AC Coupling (on oscilloscopes that support AC/DC coupling)
Current Ranges
25 A and 150 A
Max Bare Wire Voltage
600 VRMS CAT I & II
300 VRMS CAT III

Typical

DC Accuracy
±1% Typical
3% Warranted
Max Amp-Second Product
   
   25 A Range
3,000 AµS
   150 A Range
15,000 AµS
Insertion Impedance
0.03 Ω @ 1 MHz
0.075 Ω @ 5 MHz
.125 @ 10 MHz
.3 @ 20 MHz
Signal Delay
? 21 ns
Displayed RMS Noise
≤500 μARMS (probe only)

Environmental

Temperature
   Operating
0ºC to +50ºC
   Non-operating
-40ºC to +75ºC
Humidity
   Operating
5% to 95% RH (Relative Humidity) at up to +30ºC
5% to 85% RH above 30ºC up to +50ºC, non-condensing
   Non-operating
5% to 95% RH (Relative Humidity) at up to +30ºC
5% to 85% RH above 30ºC up to +75ºC, non-condensing
Altitude
   Operating
Up to 2,000 meters (6,560 feet)
   Non-operating
Up to 12,000 meters (40,000 feet)

Physical Characteristics

 
kg
lbs
Shipping Weight
.7865
1.734
Dimensions
meters
inches
Cable Length
2 meters
79 inches
Probe head size
   
   
   Length
26.8 cm 
10.55 in.
   Width
4.1 cm
1.6 in.
   Height
15.6 cm
6.13 in.
Max Conductor Diameter
21 mm x 25 mm
0.83 in. x 1.0 in.
Power Requirements
TCP0150 is powered directly by the DPO4000, MSO4000 and DPO7000 Series oscilloscopes using TekVPI interface

Recommended Oscilloscopes

DPO4000, MSO4000, and DPO7000 Series oscilloscopes with TekVPI probe interface.

Note: Requires DPO7000Series Firmware Version 3.0.2 or greater. Requires DPO4000/MSO4000 Firmware Version 2.06 or greater.
AC/DC Current Probe with TekVPI Interface.

Includes: Protective Cover (016-1924-xx), and Certificate of Traceable Calibration and Data Standard.

Option
Order
Option L0
Standard English Language Instruction Manual (071-xxxx-xx)
Option L5
Substitutes Japanese Language Instruction Manual
Option L7
Substitutes Simplified Chinese Language Instruction Manual

Recommended Accessories

Accessory
Order
Current Loop, 1 Turn, 50 Ω with BNC connector used for Performance Verification
015-0601-50
TekVPI Calibration Fixture
067-1701-xx
Cal/Deskew Fixture for DPO7000/70000 Series
067-1686-xx

Service Options

Option
Description
Opt. CA1
Provides coverage for a single Calibration Event
Opt. C3
Calibration Service 3 years
Opt. C5
Calibration Service 5 years
Opt. D3
Calibration Data Report 3 Years (with Opt. C3)
Opt. D5
Calibration Data Report 5 Years (with Opt. C5)
Opt. R3
Repair Service 3 Years
Opt. R5
Repair Service 5 Years

粤公网安备 44030502001640号